Dynamic Security Feature Affecting Cartridges Using Non-HP Security Chip

Thursday, September 14th, 2017

Yesterday customers using HP 934/950/970 cartridges using non-HP chips started seeing a “cartridge problem” message on their printers. This is not a problem with the non-HP chips but the Dynamic Security Feature on the HP printers listed below (this does not apply to any printers that aren’t listed)

Product series

OfficeJet Pro 6230 series
OfficeJet 6810, 6820 series
OfficeJet Pro 6830 series
OfficeJet Pro 8610, 8620, 8630, 8640, 8660 series
OfficeJet Pro X451dn/dw, X476dn/dw, X551dw, X576dw
If you see a Cartridge Problem error message when you are using non-HP cartridges, it is possible that a dynamic security feature has caused the printer to reject the non-HP cartridge. It is also possible that the cartridge has simply failed for other reasons.
This document applies to you ONLY if all three of the following conditions are true:
  • Your printer is in the table at the top of this document. Other HP printers are not affected.
  • You are using an aftermarket supply that contains a non-HP security chip (this may be a refilled or remanufactured HP cartridge with a non-HP chip). Only cartridges that lack HP’s security chip are affected.
  • Cartridge Problem error message displays. Other error messages are not related.

cartridge problem

Solution

HP has a firmware update that removes the dynamic security feature. The update is available only for the printers in the table in this document, because only those printers are affected.
If you would like to remove the dynamic security feature, follow these steps to download and install the firmware update:

CAUTION:

Do not use or power off the printer or computer while the firmware update is in process.
  1. Make sure the printer is on and connected to the computer, either through your network or a USB cable.
  2. Click the link for your HP printer model in the following table and run the downloaded firmware update file from your Internet browser.
Printer
Windows 7, 8, 8.1, 10
Mac OS 10.9, 10.10, 10.11
OfficeJet Pro 6230 series
OfficeJet 6810 series
OfficeJet 6820 series
OfficeJet Pro 6830 series
OfficeJet Pro 8610, 8615, 8616 series
OfficeJet Pro 8620, 8625 series
OfficeJet Pro 8630 series
OfficeJet Pro 8640 series
OfficeJet Pro 8660 series
OfficeJet Pro X451dn
OfficeJet Pro X451dw
OfficeJet Pro X476dn
OfficeJet Pro X476dw
OfficeJet Pro X551dw
OfficeJet Pro X576dw
3. Look in the HP Printer Update window to see if your printer serial number displays.
  • If the serial number is listed, select the printer serial number, and then click Update.
  • If the serial number is listed but status is not applicable (grayed out), the firmware does not need to be updated. Click Cancel.
  • If the serial number is not listed and your printer is using a network connection, connect a USB cable, wait 20 seconds, and then click Refresh.

firmwate update

4. When the update is finished, click OK.

5. If you connected a USB cable for your networked printer, then remove the USB driver that was added by Windows.

  1. Search Windows for Devices and Printers, and then open Device and Printers from the search results.
  2. Right-click the USB printer device that matches your printer model, and then select Remove Device.
  3. Disconnect the USB cable, and restart the computer.

6. If the cartridge still fails after the feature is removed, then the cartridge is most likely defective and should be returned to your retailer.


Leave a Reply

Your email address will not be published. Required fields are marked *